Swiftech MCW20 A Uživatelský manuál stáhnout pdf

Swiftech Inc., 1703 E. 28

St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769

Parts list

Parts QTY PARTS QTY

MCW20-A™ assembly 1 Nylon tension limiter 2

4-40 x 1 1/2” Philips screws 2 Spring 2

Black fiber washers 6 Knurled knobs 2

4-40 mini-nuts 2 Tube inserts 2

Arctic Alumina Thermal compound 1

This product is intended for expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to

your components. Swiftech assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The

following instructions are subject to change without notice. Please visit our web site at www.swiftnets.com

for updates.

1. Before you install the MCW20-A™ water-block:

a. Prepare two pieces of tubing of sufficient length to connect

to the rest of your circuit. The cuts must be square as shown in

figure 1 or leaks may occur:

b. Install the provided plastic tube inserts at each end of the tubes,

as shown in figure 2: these inserts are absolutely imperative when

using any kind of soft tubing, such as vynil, ClearFlex, Taigon, etc...

Square cut

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

c. Spread a little bit of grease or liquid soap

around the tubing. It helps pushing the tubes in,

particularly with Clearflex tubing, which

features a very “sticky” surface.

d. Fully insert both tubes into the fittings. The tip of the plastic tube inserts should

be flush with the inlet and outlet openings, as shown in figure 4 above. Inserting the

tubes requires a firm push, accompanied by a twisting motion.

2. Preparing your Motherboard

 Remove the motherboard from the chassis

 Remove the existing heat sink

 Carefully clean the microprocessor, using alcohol

3. Installing the MCW20-A™ water-block with AMD platform motherboards

 Install the provided screws through the motherboard, using a black fiber washer on both sides of the motherboard, and tighten the

nuts.

 Install the motherboard in the chassis

 Lightly coat the microprocessor with the provided thermal compound. Only a paper-thin coat is necessary. It should be applied using

preferably a razor blade, or a credit card, held between thumb and index at a 45-degree angle.

 TIP! It is preferable to have the tubing inserted into the water-block BEFORE you install the block onto the motherboard.

This is because pushing the tubes into the block while it is already installed could exert undue pressure onto the

microprocessor.

 Slide down the MCW20-A over the retention screws, then install the nylon tension limiters (flange facing down), the springs, and

tighten the assembly with the knurled knobs. Over tightening of the assembly is prevented by the tension limiter. Users should be

cautious nonetheless, as nylon can be easily crushed.

Page 1 of 2

1 2

Parts list 1
Page 2 of 2 2

Shrnutí obsahu

Strany 1 - Parts list

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 Parts list Parts QTY PARTS QTY MCW20-A™ assembly 1 N

Strany 2 - Page 2 of 2

Knurled knobSpringTe nsio n lim ite rflang e fa c ing do4-40 m ini-nutblack fiber washeblack fiber washer4-40 x 1 1 /2“ p h ilip s s 4. Connect th

Komentáře k této Příručce

Žádné komentáře

Swiftech MCW20 A Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Počítačové příslušenství Swiftech MCW20 A. Swiftech MCW20 A User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Počítačové příslušenství Swiftech MCW20 A